Ffmpeg2theora

ffmpeg2theora 0.28 - Xiph.Org libtheora 1.2.0alpha 20100924 (Ptalarbvorm) Usage: ffmpeg2theora [options] input General output options: -o, --output alternative output filename --no-skeleton disables ogg skeleton metadata output --skeleton-3 outputs Skeleton Version 3, without keyframe indexes -s, --starttime start encoding at this time (in sec.) -e, --endtime end encoding at this time (in sec.) -p, --preset encode file with preset. Right now there is preview, pro and videobin. Run 'ffmpeg2theora -p info' for more informations Video output options: -v, --videoquality [0 to 10] encoding quality for video (default: 6) use higher values for better quality -V, --videobitrate encoding bitrate for video (kb/s) --soft-target Use a large reservoir and treat the rate as a soft target; rate control is less strict but resulting quality is usually higher/smoother overall. Soft target also allows an optional -v setting to specify a minimum allowed quality. --two-pass Compress input using two-pass rate control This option requires that the input to the to the encoder is seekable and performs both passes automatically. --first-pass <filename> Perform first-pass of a two-pass rate controlled encoding, saving pass data to <filename> for a later second pass --second-pass <filename> Perform second-pass of a two-pass rate controlled encoding, reading first-pass data from <filename>. The first pass data must come from a first encoding pass using identical input video to work properly. --optimize optimize video output filesize (slower) (same as speedlevel 0) --speedlevel encoding is faster with higher values the cost is quality and bandwidth (default 1) available values depend on the version of libtheora your version supports speedlevels 0 to -1 -x, --width scale to given width (in pixels) -y, --height scale to given height (in pixels) --max_size scale output frame to be within box of given size, height optional (%d[x%d], i.e. 640x480) --aspect define frame aspect ratio: i.e. 4:3 or 16:9 --pixel-aspect define pixel aspect ratio: i.e. 1:1 or 4:3, overwrites frame aspect ratio -F, --framerate output framerate e.g 25:2 or 16 --croptop, --cropbottom, --cropleft, --cropright crop input by given pixels before resizing -K, --keyint [1 to 2147483647] keyframe interval (default: 64) -d --buf-delay <n> Buffer delay (in frames). Longer delays allow smoother rate adaptation and provide better overall quality, but require more client side buffering and add latency. The default value is the keyframe interval for one-pass encoding (or somewhat larger if --soft-target is used) and infinite for two-pass encoding. (only works in bitrate mode) --no-upscaling only scale video or resample audio if input is bigger than provided parameters --resize-method <method> Use this method for rescaling the video See --resize-method help for a list of available resizing methods Video transfer options: --pp Video Postprocessing, denoise, deblock, deinterlacer use --pp help for a list of available filters. -C, --contrast [0.1 to 10.0] contrast correction (default: 1.0) Note: lower values make the video darker. -B, --brightness [-1.0 to 1.0] brightness correction (default: 0.0) Note: lower values make the video darker. -G, --gamma [0.1 to 10.0] gamma correction (default: 1.0) Note: lower values make the video darker. -Z, --saturation [0.1 to 10.0] saturation correction (default: 1.0) Note: lower values make the video grey. Audio output options: -a, --audioquality [-2 to 10] encoding quality for audio (default: 1) use higher values for better quality -A, --audiobitrate [32 to 500] encoding bitrate for audio (kb/s) -c, --channels set number of output channels -H, --samplerate set output samplerate (in Hz) --noaudio disable audio from input --novideo disable video from input Input options: --deinterlace force deinterlace, otherwise only material marked as interlaced will be deinterlaced --no-deinterlace force deinterlace off -f, --format specify input format --inputfps fps override input fps --audiostream id by default the first audio stream is selected, use this to select another audio stream --videostream id by default the first video stream is selected, use this to select another video stream --nosync do not use A/V sync from input container. try this if you have issues with A/V sync Subtitles options: --subtitles file use subtitles from the given file (SubRip (.srt) format) --subtitles-encoding encoding set encoding of the subtitles file supported are utf-8, utf8, iso-8859-1, latin1 --subtitles-language language set subtitles language (de, en_GB, etc) --subtitles-category category set subtitles category (default "subtitles") --subtitles-ignore-non-utf8 ignores any non UTF-8 sequence in UTF-8 text --nosubtitles disables subtitles from input (equivalent to --subtitles=none) --subtitle-types=[all,text,spu,none] select what subtitle types to include from the input video (default text) Metadata options: --artist Name of artist (director) --title Title --date Date --location Location --organization Name of organization (studio) --copyright Copyright --license License --contact Contact link --nometadata disables metadata from input --no-oshash do not include oshash of source file(SOURCE_OSHASH) Keyframe indexing options: --index-interval <n> set minimum distance between indexed keyframes to <n> ms (default: 2000) --theora-index-reserve <n> reserve <n> bytes for theora keyframe index --vorbis-index-reserve <n> reserve <n> bytes for vorbis keyframe index --kate-index-reserve <n> reserve <n> bytes for kate keyframe index Other options: -P, --pid fname write the process' id to a file -h, --help this message --info output json info about input file, use -o to save json to file --frontend print status information in json, one json dict per line Examples: ffmpeg2theora videoclip.avi (will write output to videoclip.ogv) ffmpeg2theora videoclip.avi --subtitles subtitles.srt (same, with subtitles) cat something.dv | ffmpeg2theora -f dv -o output.ogv - Encode a series of images: ffmpeg2theora frame%06d.png -o output.ogv Live streaming from V4L Device: ffmpeg2theora --no-skeleton /dev/video0 -f video4linux \ --inputfps 15 -x 160 -y 128 -o - \ | oggfwd icast2server 8000 password /theora.ogv (you might have to use video4linux2 depending on your hardware) Live encoding from a DV camcorder (needs a fast machine): dvgrab - | ffmpeg2theora -f dv -x 352 -y 288 -o output.ogv - Live encoding and streaming to icecast server: dvgrab --format raw - \ | ffmpeg2theora --no-skeleton -f dv -x 160 -y 128 -o /dev/stdout - \ | oggfwd icast2server 8000 password /theora.ogv